Project Round Up! 11th of August 2018

Heya!

Just wanted to do a bit of an update on all current project I’m working on at the moment. Most projects are on hold as I’m a one man crew with limited free time and since I’m taking commissioned work, I don’t really have the time to work on everything. I’m usually working on 2 projects at once: Commission stuff first and then personal stuff if I have some time in the week ends. I won’t list things I wanna make, just projects I have actually started. Some of them will be finished, some of them might not due to a lack of time. Let’s do a round up!

F-11D Blaster from Star Wars (Commission)

State of the project: “Non LED” version was made one or two years ago. The goal of this commission is to add LEDs and improve the 3D model.

Features: Red side LED and front lamp. Also, the front handle was glued on the previous version so I added a small snap mechanism to have it movable. I also took the time to tweak how the model was split for printing to gain sturdiness and to help save some time during post process


N7 Crusader from Mass Effect (Commission)

State of the project: DONE!

Features: None, just a painted prop.


N7 Valkyrie from Mass Effect (Personal Project)

State of the project: 3D model is almost done. I need to slice it up intelligently for 3D Printing.

Features: None, just a painted prop. Might add LEDs if it’s not too much trouble.


M7 Caseless SMG from Halo:3 & Halo:3 ODST (Commission for family/friends)

State of the project: ODST Version is done!

Features: Retractable butt and front handle, Removable clip, sight and silencer for the ODST version.


Custom Light Saber (Personal Project)

Further discussed here

DfzdWhJW4AAzrG8


Data Knife from Titanfall 2 (Personal Project)

State of the project: I already made a regular Data Knife a while ago but with no electronics whatsoever. I’m still figuring things out as space availability is rather thin.

Features: LEDs animations when trigger is pulled. A small video is available here


R201 Carabine from Titanfall 2 (Personal Project)

State of the project: Just started the 3D model and as usual, Titanfall 2 props are highly detailed and require A LOT OF TIME.

Features: Removable mags. Maybe more stuff as I go along.


L-STAR from Titanfall 2 (Personal Project)

State of the project: 3D model is almost done. I need to slice it up a bit and optimize everything for 3d printing without compromising ease of assembly and electronics accessibility. I got the electronics almost sorted out but since I learned new tricks with the lightsaber project, I might go back and change a few things

Features: Trigger responsive rotating parts. LEDs.

Here a small timelapse of my first 3D modeling sessions:

And here’s another small video from my Twitter account of the electronics that will go inside it


SE-44C Blaster from Star Wars (Personal Project)

State of the project: 3D Model still in the making.

Features: TBD


 That’s all folks!

I actually have some other stuff but I wanted to focus on the more defined projects. I’m also learning Zbrush to be able to tackle more organic designs like this Harry Potter Elder Wand I made a few month ago. Perfect to start practicing Zbrush!

HPEW_4

 

N7 Crusader is done! – Project Updates!

Heya!

 

I’ve finished the N7 Crusader! but let’s start this post where we left the previous one. I was wetsanding the hell out of it and I continued. The was coat is usually a black or grey primer that I sand down at either 400 or 600 grit (or higher if I need a super shiny paintjob).

20180710_180427

Once it was done, I applied a black primer and started applying the base coats with my airbrush.

20180712_105745

I made myself some 3D Prnted stencils to make the N7 logo and the red/white strips.

 

I assembled and glued everything, weathered and added some shadow in the right places. The photo album can also be found on my facebook page

N7Crusader_9

Aaaaaand that’s all for that commission (actually, no I have a bit of customizing to do for the person who commissioned me. She wants the paragon/renegade logo on both side of the handle). So what’s next? I got a few customs paintjobs to do that I’ll post when they are done.

 

 

N7 Crusader WIP – Project Updates!

All current personal projects are on hold for a few reasons:
First, I’m waiting for parts to be shipped (mostly for the lightsaber project, which is #1 on my personal list cause I want one so bad)
Secondly, I’ve been too busy repairing my printers: There was a big heatwave in France and my printing room was about 40°C-45°C which is a bit too hot for the electronics. The steppper motors start to miss some steps meaning I ended up having either some light later shifting or under extrusion (or a bit of both) in the early afternoon (when the heat was at it’s maximum)
Last reason: Personal projects are on hold because commissioned work is always prioritized, which brings me to the main point of this blog post: the N7 Crusader.

Despite the crushing heat, I was able to print everything in a few days thanks to my 5 Ultimaker UM2+.

20180706_185512

The main body is locked to the humongous canon part with PVC tubes and a metal rod to straighten everything. At this point, nothing is glued. I usually glue everything near the end of the project, after base colors are applied cause having separate parts eliminate the need to use mask tape and thus makes painting way easier. But before I can do any painting, I need to fill and sand down everything multiple times to get the surface smooth. I usually raw sand at 80 (120/240 for detailed spots) first, then apply a few coats of filler, raw sand again and fill one more time before doing some wet sanding (120/240)

20180709_181314

And here is what I have so far. I’m gonna do a couple more sanding/filling sessions with 240/400 sandpaper and then I’ll be able to prime it and start painting it.

20180709_211428

 

Project Round Up! 27th of June 2018

Heya!

Just wanted to do a bit of an update on all current project I’m working on at the moment. Most projects are on hold as I’m a one man crew with limited free time and since I’m taking commissioned work, I don’t really have the time to work on everything. I’m usually working on 2 projects at once: Commission stuff first and then personal stuff if I have some time in the week ends. I won’t list things I wanna make, just projects I have actually started. Some of them will be finished, some of them might not due to a lack of time. Let’s do a round up!


N7 Crusader from Mass Effect (Commission)

State of the project: 3D model is 100% done. It is sliced up and ready to be 3D printed!

Features: None, just a painted prop.

N7 Valkyrie from Mass Effect (Personal Project)

State of the project: 3D model is almost done. I need to slice it up intelligently for 3D Printing.

Features: None, just a painted prop. Might add LEDs if it’s not too much trouble.


M7 Caseless SMG from Halo:3 & Halo:3 ODST (Commission for family/friends)

State of the project: Prototype is ok but 3D model needs some tweaking.

Features: Retractable butt and front handle, Removable clip, sight and silencer for the ODST version.


Custom Light Saber (Personal Project)

Further discussed here

DfzdWhJW4AAzrG8


Data Knife from Titanfall 2 (Personal Project)

State of the project: I already made a regular Data Knife a while ago but with no electronics whatsoever. I’m still figuring things out as space availability is rather thin.

Features: LEDs animations when trigger is pulled. A small video is available here


R201 Carabine from Titanfall 2 (Personal Project)

State of the project: Just started the 3D model and as usual, Titanfall 2 props are highly detailed and require A LOT OF TIME.

Features: Removable mags. Maybe more stuff as I go along.


L-STAR from Titanfall 2 (Personal Project)

State of the project: 3D model is almost done. I need to slice it up a bit and optimize everything for 3d printing without compromising ease of assembly and electronics accessibility. I got the electronics almost sorted out but since I learned new tricks with the lightsaber project, I might go back and change a few things

Features: Trigger responsive rotating parts. LEDs.

Here a small timelapse of my first 3D modeling sessions:

And here’s another small video from my Twitter account of the electronics that will go inside it


SE-44C Blaster from Star Wars (Personal Project)

State of the project: 3D Model still in the making.

Features: TBD


 That’s all folks!

I actually have some other stuff but I wanted to focus on the more defined projects. I’m also learning Zbrush to be able to tackle more organic designs like this Harry Potter Elder Wand I made a few month ago. Perfect to start practicing Zbrush!

HPEW_4